選擇其他國家或地區以查看您所在位置的內容。
美國
16:47:24 GMT+0000 (Coordinated Universal Time)
產品資訊
公制
英制
主要尺寸和性能資料
| B1 | 86 mm | Total Width |
| H | 82 mm | 高度 |
| L | 155 mm | 長度 |
安裝尺寸
| D86 | 70 mm | |
| D87 | 80 mm | Ø Bolt circle |
| d85 | 20 mm | |
| d86 | 61 mm | Ø Inner Fit |
| L88 | 25 mm | |
| G43 | M8 | Thread |
| G87 | M6 | Thread |
| h85 | 41.5 mm | |
| JB43 | 59 mm | |
| JL43 | 100 mm | Tolerance ±0,2 |
| jB8 | 43 mm | |
| NB85 | 6 mm | Width of Keyway |
| NL85 | 16 mm | Length of Keyway |
| NT85 | 3.5 mm | Depth of Keyway |
| T86 | 2.3 mm | Depth Fit |
| Tol T86 up | 0.3 mm | Upper tolerance |
| Tol T86 low | 0 mm | Lower tolerance |
| t43 max | 14 mm | Depth of Thread |
| t87 max | 12 mm |
尺寸
| B2 | 75 mm | Width of Support Rail |
| B4 | 74 mm | Width of Return Unit |
| B18 | 15 mm | |
| B72 | 2 mm | |
| H1 | 32 mm | |
| H2 | 66.5 mm | 高度 |
| H4 | 81.5 mm | Height of Return Unit |
| H7 | 47 mm | |
| H18 | 40 mm | |
| h13 | 25 mm | |
| h18 | 5 mm | |
| L2 max | 16,000 mm | Maximum length of Support Rail |
| L4 | 80 mm | |
| L18 | 300 mm | |
| LTn min | 500 mm | Support Rail in Segments length min |
| LTn max | 8,000 mm | Support Rail in Segments length max |
| FBL | 1.44 | Effective length factor of bellow |
| S | 85 mm | Dimension |
Technical data
| mLAW | 0.73 kg | Mass of Carriage |
| m1 | 1.22 kg | Mass of Connecting Plates of Profiles |
| vmax | 8 m/s | Maximum Speed |
| amax | 40 m/s2 | Maximum Acceleration |
| Rx | 60 mm | |
| Ry | 20.5 mm | |
| Rz | 54 mm | |
| I C | 4,100 N | Load direction I: compressive load |
| I C0 | 2,400 N | Load direction I: compressive load |
| II C | 4,100 N | Load direction II: tensile load |
| II C0 | 2,400 N | Load direction II: tensile load |
| III C | 6,600 N | Load direction III: lateral load |
| III C0 | 4,200 N | Load direction III: lateral load |
| M0x per | 30 Nm | Max. permissible static moment per Carriage 1 |
| M0y per | 130 Nm | Max. permissible static moment per Carriage 1 |
| M0z per | 70 Nm | Max. permissible static moment per Carriage 1 |
| Iy | 104 cm4 | Geometrical moments of inertia of Support Rail 2 |
| Iz | 76 cm4 | Geometrical moments of inertia of Support Rail 2 |
附加資訊
18 Nm | Max. permissible drive torque | |
4 x LFR50/8-6-2Z | Track Rollers | |
0.1 mm | Repeat Accurancy ± | |
175 mm | Feed (mm/rotation) | |
20AT5 | Toothed Belt | |
0.068 kg/m | Mass of Toothed Belt | |
640 N | Permissible Toothed Belt operating force | |
2.2 kg*cm2 | Mass moment of inertia of Gears |
溫度範圍
| Tmin | 0 °C | Minimum operating Temperatur |
| Tmax | 80 °C | Maximum operating Temperatur |
註腳
1
The values are single loads and apply when the underside of the actuator is fully supported. If there are several carriage units per actuator or combined loads are present, these must be reduced.
2
Moment of inertia of area of “closed” support rail (= support rail without free milled area on base). In comparison with these values, the moment of inertia of area Iy of the side with the free milled area on the base is reduced to an insignificant degree and the moment of inertia of area Iz is reduced by approx. 10%.
下載：
您當前的產品型號
| 尺寸碼 | 32 | |
| 支架長度 | 155 | 155 mm |
| 保持架設計 | 標準 | 標準支架 |
| Drive type | (3)ZR | Toothed belt drive |
| Additional carriage | / | No additional carriage |
| Support rail design | FA517.1 | Two-piece |
| Bellow | FBALG | Yes |